How to take out an old toilet bowl. Do-it-yourself dismantling of the toilet bowl with different methods of fixing How to turn on the toilet bowl from the sewer

For the sake of changing the interior of the toilet, the Lord rarely fills up the old toilet bowl. Tsey plumbing virіb can start not only physically, but also morally. For example, nіnі rіdko zustrіnіsh vpryadkovanih apartments modelі z transverse plank, tse radar rarity.

When doing practical dismantling of the old toilet bowl with your own hands, the master needs to follow a number of rules. And the decision to perform this operation on your own may be due to many reasons:

  • Saving money on weekly fahivtsya;
  • Pragnennya to control especially the quality of the installation;
  • The prospect of being able to graduate to a professional.

As if the reason did not spur the vlassnik of power to the tsy krok, it’s the last succession of the children of the old plumbing.

Preparatory work

The first step is to promptly dismantle the old toilet bowl, it is necessary to carry out a series of clumsy manipulations:

  1. Close the tap on the water supply, so that the water stops coming in.
  2. It is necessary to drain all the water from the tank, if anything inner surface wiped with a hygroscopic material (sponge, ganchir'yam thinly).
  3. Twisting a flexible hose that supplies water to the tank. It's important: it's easy to miss the manipulation of the hose, and the axis of the traces of this is more serious: communications can be broken, the body of the toilet bowl can be broken.
  4. Promiti toilet bowl and descent into the water seal, after which dry these areas with an old towel or other material with good characteristics, which should be taken;
  5. It is necessary to think over the “route” of transferring the dismantled bin, because Zayvi ruhi body with an important subject is not the best thing to do.

Do-it-yourself dismantling of the toilet bowl is less likely after rechecking the water content of the toilet in the cistern and the water seal in the cistern. Less than a second, you can go to the next stage of work.

Set of tools

The maestro will need stepping tools to replace the toilet bowl:

  • Standard wrenches in a set (from No. 10 to No. 14) are necessary for twisting bolts and nuts to fix the toilet bowl;
  • Pliers, two keys (No. 1 pipe, rose) for work with plumbing communications.

Dismantling procedure

Sequence of work:

  1. For the cob of varto, a cistern will pop up, making it easier for the whole construction itself;
  2. Even though the fastening rusted, or it was covered with vaping pads in the presence of condensate, and a different tool for twisting nuts is victorious. In lonely vipadkahs, the elements of skrіplennya can be cut off;
  3. Attachment to the toilet at the bottom - 2 self-tapping bolts, yakі need to be screwed. If you need to report zusillya for an hour of vikonannya cієї manipulations, you can blow the toilet bowl;
  4. The old models of plumbing were installed from the concrete foundations, it is practically impossible to dismantle such a vibrator without some damage. To this, the master is guilty of pragnet to a neat beat of a concrete screed for an additional hammer and chisel;
  5. The manager of the skin master, who called for independent dismantling of the toilet bowl, swears at the saving sewerage system in good condition without harm to further functioning.

As in the process, remember, it’s especially not varto to get embarrassed. It may be due to the presence of cracks, a factory blueprint, or the completion of a guaranteed term for its operation.

Possible problems

It is to blame for the whole and not the mother of cracks in the result of the unsatisfactory dismantling of the old sanitary ware. If the master overdoes it with a grinder with keys, it is a risk of the need to replace the whole riser!

It is also necessary to take care of tidiness, so that the toilet bowl tricks, or the clothes of the great mind were spent in communication. At the link with the cim, it was categorically fenced off for the hour of the old plumbing:

  1. Tap with a hammer on the sewer pipes, regardless of the material being prepared (plastic, chavun or metal);
  2. Clean the walls of the branch pipe without installing a polyethylene plug at the outlet of the riser.

Video about independent replacement of the toilet bowl

Vikonuyuchi all vyscheperelіchenі rules and please, be it any kind of bazhayuchy you can remember the toilet bowl, which has become the main one, for a new, modern and functional model.

How can you vikonati dismantling the toilet bowl with your own hands? Have tsіy statti mi dekіlka typical methods fixed toilet bowls and cisterns. For dermal retraction, the sequence of operations for dismantling will be described.

Tank dismantling

The dismantling of that installed toilet bowl can be removed, that the old cistern is removed. Z tsієї operation ї i pochnemo.

Upper tank

Given: a tank of fastenings on the wall behind additional studs, welded to steel smuga. Smuga has been shot to the wall with a mounting gun.

Go to the toilet with a gum cuff.

  1. We turn the water over to the tank and let the water in.

To win respect: in old budinkas it is possible to get a quick lead up to the cistern.
The filling valve is screwed into the chavun coupling screwed onto the threaded pipe.
In order to understand, without destroying the entrance to the riser, you should drink it with a blowtorch or a gas burner.

  1. Take off the lid of the tank.
  2. Screw nuts, yak trim yoga on stilettos.
  3. After pushing the pouring pipe back, we lift the cuff from the toilet bowl..
  4. We take a tank with studs and put it on a flat surface.

A compact of viticulture

Rice yogo vikonannya is characteristic - okrema polichka.

From the socket of the toilet bowl, it is closed with a cuff, but not at the sight of two cylinders of different diameters, like at the front slope, but at the shape of a cut cone.

  1. We turn off the water and turn on the supply.
  2. Rozkruchuemo chat between the toilet bowl and Polichka. Like a plastic stink - it’s easy to crush with bare hands; for brass you need pasatizhі or rіzhkovі keys. Steel bolts will inevitably rust for the fates of exploitation; It’s better to cut them down, having cut them with a cloth like a hacksaw for metal.
  3. We give the police back and we swipe it from the cuffs.
  4. We know the tank and put it on a flat surface. Let's remove the cuff from the toilet bowl.

Imported compact

The dismantling of the toilet bowl - the old broken one - imported glass is also better than the dismantling of the cistern.

  1. We turn on the supply and pour water.
  2. Let's talk loudly to attract the police.

Porada: look at the police.
It’s quite possible that you don’t need tools: in bagatioh sets of nuts, you can make handy rams.

  1. We take the tank and remove the caliper gasket from the shelf.

Dismantling the toilet bowl

How do you see the dismantling of the old toilet bowl to lie down in a way, like in the installations, and in the fact that you need the old set of cylinders.

Gwenti installation

The most simple dismantling operation is in that case, if the compact is installed on the staff, and the outlet is connected to the sewerage pipe with a rubber seal or a cuff.

  1. Significantly decorative pads on the upper part of the sole. Under them, the heads of the screws appear under the twist or the key.

  1. Vikruchuemo gvinti (їх 2 or 4).
  2. Vityagaemo release from the pipe. Right shattered.

Installation on taffeta

In the wartime life, it was widely practiced to install sets with an upper cistern on taffeta - tovstu doshka, laid at the top of the ceiling.

Reveal respect: the deplorable camp of the boards of the poor is explained by the broken technology of installation.
On the back of the hand it was possible to vicorate more than oak planks; prote z mirkuvan ekonomії u khіd went pine and іnshі nestіykі to rotting breed.

The main problem is that the release, as a rule, of taps from the sewer pipes.

How to dismantle the toilet bowl?

  1. Having turned with a small twist with a small hammer, we break the cement putty near the outlet.
  2. Tієї well, with a twist, you can pull out the maximum amount of cabal from the pipe - oiled organic fiber, which was used to carve the z'ednannya.
  3. Let's twist the screws (or just pull them out of the plank, which is rotten) and, trochs are stolen, it's easy to release from the socket.

Mounted on cement

The installation and dismantling of the toilet bowl on the cement gap leaves at least a chance to beat it again. Smearing with a rosemary on the entire depth of the pipe, the release sounds roar when you try to winnow yoga.

If you still want to try it - go ahead.

  1. Virubuyemo with a twist and a hammer maximum cement from the pipe.
  2. Let's sweat with deadly strength with a foot (at the vzutti, sensibly) from the bottom uphill under the bowl in front. After one - two strikes of the foot will ring. Chi vtsіlіє at tsomu release to fall in the middle of the spring.

Visnovok

Like bachite, dismantling the toilet with your own hands does not become especially difficult. The video has first-hand information on this topic. Success!

Plumbing equipment, like and be-like else, not forever. It's too early to come the hour of dismantling the fittings that served their own. From the bathroom or the sink, everything was more or less understood. And how to remove the toilet bowl without problems and serious ruins, you know, far from leather. The procedure is unacceptable. However, if you take the right hand correctly, you won’t take a lot of time and pass with the minimum expenses for admission. Vikonati dismantling is possible independently.

In front of the cob, it is necessary to make a toilet bowl and do yoga, be a kind of disinfectant. Otherwise, if you want to rinse with an antiseptic water spray, for example, the famous “Blizni”. In case of a sudden dismantling, it is better to carry out dismantling in cold mittens, in order to protect your hands from confusion and microtraumas. With tools, it is necessary to prepare a crowbar and keys of various roses. In addition, you need a cebro and a rich ganchir.

Dismantling an old outbuilding is not the best job, it’s impossible to install a new appliance without it

I work in the area next to the same number of inputs. We take away everything that is in uninterrupted proximity to the possession. Sewerage may be inactive. Therefore, not only do you yourself not reproach her, but in advance of the judgment about the conduct of the work, we ask you to do it yourself. Let's cut off the water supply, which goes to the fitting, and pour water from the tank. Now you can rozpochinati bezposerednіy dismantling of plumbing outbuildings.

The main stages of dismantling the structure

  • We repair the hose that supplies water to the tank.
  • If so, you can dismantle the tank itself. It’s not necessary to be afraid, but it will be more important to clean up the toilet bowl at once. We check that the water is not left in the tank, pushing the drain button, and turning the fixing nuts. We know attachment. Tse is true for cisterns, installed directly on the toilet bowl. If you want to fit on the wall, dismantling will be extremely simple. Yoga is simply known from the loops.

Before taking out the tank, obov'yazkovo poured out the new water

We add the basis

The procedure can be carried out in different ways, fallow in the type of fixed toilet bowl. The modern outbuildings are fixed to the underlay for additional special fastenings, installed at the lower part of the bowl. It's easy to do it and twist the foundation yourself. The simplest option. The studs don't get in the way either. It is necessary to remove the nuts that are screwed on them and to loosen the basis of the possession.

The toilet bowl can be embedded in the cement base of the underlayment, and the tile is laid after it. At this point, the lining is dismantled, the lower part of the outbuilding is being opened. I, nareshti, himself folding way fastening - "on taffeta". Vіn peredbachaє prilada prilad on the plate, embedded in the lining. For dismantling, the lower part of the toilet bowl needs to be cut, so that the foundation was lost at once from the fasteners. Then, in parts, the surpluses will be built and a doshka.

Like a toilet bowl creaking on taffeta, dismantle it yourself.

Vіd'єdnuєmo toilet bowl vіd kanіzіynoї pipe

Now the toilet is connected only with a sewer pipe. Vіd'єdnati yogo can be done in many ways, which are divided for labor. The choice of the method to lie down, in addition, it is important to carry out the work with a minimum of rubbish and it is necessary to save the toilet bowl. In case of a flutter in front of the cob, it is necessary to prepare a cork, which the sewer pipe will curl up at the same time. You can also use a gag from old ganchiros. Vіn zapobіgatimé consumption of sewer gases before the application. Now you can rozpochinati dismantling.

  • The most simple, the most ruinous way, the way - just cut the introduction into the fitting. At this point of the dekіlkom, with exact hands, the outlet of the toilet bowl is opened in the outbuilding, after which the sewer pipe is resolutely cleaned in the form of ceramics and overflows. You can try it so hard. The stick is cleaned as much as possible and blown into the hole. Raise the toilet bowl and sharply smack yoga uphill, forcing the entrance. Then it will be necessary to carefully wilt the mustaches from the sewer pipe.

When using such a technique, it’s important not to smear the sewer pipe with tricks, otherwise there will be problems with the operation of the new fixture.

A plug in the pipe is necessary to prevent the appearance unacceptable smell in the host

  • As a toilet bowl is needed, such an option is victorious. A plot of land with a sewer pipe is resolutely cleared of the difference, narrowing it down. For whom we take a thin chisel, that carefully, with light blows, we scrape the material. In the case of the tool, it is best to install it across the coating, so the ability to crack the blade is minimal. After that, as the crack on one side gives a crack, we move on to the next story. The coating, which cracked, is carefully removed. Let's add lightly to it and reverify it, let's start to collapse in the pipes and just like that, then it's easy. Rozgoduєmo and scroll through the introduction, slowly wailing yoga trumpets. I’ll build it up, I’ll protect it, clear the passage. Vyynyavshi tsiliy toilet, vіdstavlyaєmo yogo killed and relatively cleared the pipe, getting ready for further installation.

Gently clean the base of the toilet bowl before dismantling

We install a timchasovy toilet bowl

Timchasov obladnannya is simply necessary, as it is planned to carry out repairs in the bathrooms. In such a situation, attachments are installed without cistern. So yoga will be easier for the need to take it and clean it up. For zmiv vikoristovuyut cebro with water. Shchob pristriy standing mіtsno, under the new one, a piece of chipboard or a shield is laid. At the new one, through the opening of the fixing, close the toilet bowl, vicorist for that self-tapping screw with washers. From the sewerage, the attachment is hung up at the looking corrugations. Now yoga can be credited for recognition. For the protection, I will build a vіd zabrudnennya pіd hour of repair robots, you can wrap it with cellophane and fix it with tape.

A small nuance: the line should be glued only on the plate, otherwise it will be important to remove the excess from the surface attachment.

The scheme of competent dismantling of the toilet bowl

Dismantling the old toilet bowl - to make it easy, even if it’s not even a receptionist. Behind him, it’s possible to get a little plumber, especially as a possession that has served its own, it’s planned to just kick it and there are no reasons to talk about its integrity. It is better to carry out the dismantling in such a way that the old fixture is left unfinished, and the destruction in the sanitary facilities will be minimal. In this way, you need the same novice and patience. There is no such thing as such, but there is no need to bother with plumbing, to turn to professionals. The stench is quick to carry out a competent dismantling of possessions, breaking through the zavdannyam, be it folding.

Video: dismantling the toilet

Today we will tell you about those who can be vikonati toilet dismantling without receiving outside help. Adzhe buvayut such situations in life, if no one is afraid, they simply do not get the help of the plumbing technician.

Zvichayno for fahіvtsya similar to the robot is not a warehouse of special difficulties. I all the same. Itself to that we will not give rise to flies of an elephant. Try to briefly describe all the events in order.

Knowing the toilet bowl self-tightening. Etapi

In order to remove the toilet on your own, we recommend that you do it strictly in stages. Let's take a look at 3 main stages, which should be included in them and how to do it, in order to avoid additional charges for the repair of sublogs and walls.

Stage 1. Preparation of work

For the cob of work, we need a small crowbar, wrenches, pliers, non-necessary ganchirks, gum mittens and zasib for disinfection. It is necessary to wear only gloves in mittens, and the entire working space must be left as much as possible in the form of smittya and brud. You can vikoristovuvaty as a special zasib, scho disinfection, so simple chlorine. Navit vіdbіlyuvach pіdіyde.

  1. I again turn off the cold water with a valve.
  2. Water, which is poured from the tank.
  3. We check that the water is blocked again and proceed to the main work.

Stage 2. Improvement of the base of the toilet

Do not dismantle the base at once from the tank. It's not obvious. For the cob you can see a flexible hose, through which water is supplied. If so, you can take the tank. If you just hang on the hinges, you can wind it up without breaking it. How to fasten with nuts from the tiled side, it is necessary to unscrew them.

Then you can proceed to the dismantling of the base. Fallow in the model of the toilet bowl creak at 2 or 4 points. As a rule, z'ednannya haykove. Abo is a dowel. Nezalezhno vіd tsogo, you can win the key for dismantling. Give respect to the fact that you have laid a kahel on your bed, you may have broken the troch. Otherwise, dismantling the base is not enough.

Like a toilet bowl to stand on stilettos, it is necessary to lift a little bit and steal it, by the same token it is necessary to fix a hole in the sewer pipe. Like the toilet bowl is cemented, the cement can be beaten with a chisel. It is only necessary to direct the yoga wind across the coating, so as not to damage the outlet or the pipe.

Stage 3

At this stage, a single toilet is installed - with a sewer pipe. Before that, as we saw it, a gag was prepared, so that it would be possible to close the pipe and block the exit of sewer gases.

The simplest way is to introduce a pipe into the pipe, after which you clean the surface from the particles of ceramics and the old rozchin. It dawned on me that in this situation, it would be impossible for the toilet bowl to be farther away. If you plan to install yoga, for example, at the dacha, then diemo іnakshe.

It is believed that the toilet bowl is collapsing at the pipe. If it is enough hitaєmo and scroll through, until you see the pipe from the pipe. On a new one, better for everything, a little bit of a rozchin will be lost, which happens to be neatly put in front of the installation of new plumbing.

Dismantling the old toilet bowl

Here can be a folding robot. At the houses/apartments, which were outside the Radian hours, the plumbing was installed as superbly as possible and, in fact, did not transfer to dismantling. Itself to that without significant poshkodzhen not to do.

Take out the toilet, do not mess with yoga, do not go into it. You may not try. The sticks will be crushed, the shards of the stench will be hermetically sealed with cement. It’s a smut here - don’t mess with the sewer pipe and that outlet. It’s not worth talking about those who, if wielded with a chisel and a hammer, should be protected by the edge, as we wrote earlier, to direct yoga across the coating.

As you can understand, dismantling the toilet bowl with your own hands is not so easy. If you want to spare the good in the services of a plumber, just take care of our joys.

Do-it-yourself installation of a toilet bowl is a busy task, and the use of simple skills and tools. However, if you work independently, then, in the first place, you can save on fahіvtsya, in a different way, gain priceless evidence - even if it’s new in the future, you’ll be correct.

Toilets, zvazhayuchi on their own design, vіdrіznyayutsya for the method of installation. The widest view is sublingual.

Necessary items

Before that, how to install the toilet bowl with your own hands, it is necessary to perekonatisya at the presence of objects, as you need from your right:

  • perforator;
  • Rose and wrench;
  • Hammer;
  • twists;
  • sealant;
  • Transfer cuff for connecting to a chavun socket;
  • Єmnіst, where the water from the plumbing outbuilding is getting angry, which is being dismantled, as well as the ganchirka, to wipe it.

Preparation

Before that, as if remembering the toilet with your own hands, you will need to prepare to come in. It is necessary to sign the back, in some way the new attachment will be connected to the sewer. Three cuff options:

  • Corrugated - such a way of connection is economically viable. However, with this method, installation cannot be carried out right up to the sewer pipe.

Before that, like connecting a toilet bowl behind an additional corrugated cuff, it was necessary to change it, so that the room could have the necessary space, and handily accommodate the possessions.

  • Straight is a universal way of connecting, which allows you to work independently. Yakshcho vynikli kolivannya at the choice of the method of connection to the sewerage, this option is the best.
  • Eccentric - the method of connecting to the sewerage system, which is handy in that case, as if the center is angry and the pipe is replaced.
Connecting the toilet for help cuff

To properly install the toilet with your own hands, it is recommended to dismantle the old installation and install a new one. Dovzhina її is obliged to add water to the air supply pipe to the toilet bowl, plus 15-20 cm.

Dismantling

Before that, how to change the toilet bowl, it is necessary to dismantle the old one. For whom do you need:

  • Turn off the feed;
  • Vimknuti pіdvedennya;
  • Anger vmist іz barrel;
  • Take a dizhka. As if the old toilet bowl is not planned to be beaten anywhere, it can be beaten with a hammer, otherwise it can be done carefully;
  • Take out the crimping tools, for the help of which, the installation of the bowl was carried out, you could see it, having poured out the water, what was left out.

As for the dismantling of the old toilet bowl, it is necessary to use brute force and beat a hammer or a puncher, then we will protect it, so as not to allow dangerous tricks to get into the sewer, which will cause confusion.

As if under an old bowl, as if it were a support from a tree of another material, it is necessary to see it. Empty, which was lost after the last operation, may be filled with cement and smoothed with a spatula.

http://www.youtube.com/watch?feature=player_embedded&v=Y1XRh22HZKE

Toilet installation

  • Before that, how to put the toilet on your own, it is necessary to clean the pipe in the form of irzhі that zabrudnen. Then it is necessary to cover with sanitary sealant and attach the cuff.

If the toilet is dismantled, odors come out of the sewers. So that the stench did not come out of the work, the opening of the sewers must be closed, for example, shut up with ganchirs.

  • Do-it-yourself installation of the toilet bowl is carried out with a rosette under the dowels. For which bowl is placed in those places, de may be broken and installed, and the opening of the opening is fixed. According to this rosette, open it and insert dowels into the opening.

For some models, open the holes under the hood. In such a way, to put the toilet in the open, you need to drill under the same hood.

  • If dowels are inserted, the bowl is placed on its own place, and joins with a cuff from the sewer socket. Then the screws are twisted, plastic washers are pulled into the yak.

It is not right to tighten the screws too much. It’s easy to make a small cobweb, and evaluate that the installation has been broken. If not, then turn it off, substituting a new lining made of plastic. Less than a second can be tightened.


Installation of the bowl is carried out behind a rose
  • To install the toilet bowl, it is necessary to build a folded barrel on your own, as if you were setting it up for a chosen one. Here everyone is asking for instructions on what to do with the picker.

All the rough details are not to blame for one of the walls of the pouring tank.

  • The next stage is the installation of the pouring tank on the bowl. The fastening of the sound is carried out for the help of bolts, yakі slіd twirl evenly. If the installation is vikonano, a cover is put on the tank and a button is installed, otherwise it is important to zlivu.
  • The final moment of independent installation of the toilet bowl is the connection of the water supply.

If the water is turned on, do not hurry to get the water out. The back of the head needs to be checked visually for the details of the design. Just remember that everything looks normal, you can fill up the water, fill the reservoir and try to save. Yakshcho vynikli protіkannya, їх it is required to suck.